Fountain Pen Restoration

Long Short Pens

I recently received a very nice long short pen from Pen Maker Darrell Eisner, from Nova Scotia. It is shown here both open and closed.  It is a cartridge filler and made of solid metal. I have been carrying it in my pocket due to its durability. After receiving it and putting it to use, it reminded me that I have a couple of vintage long short models that need restoration and have been  sitting on the workbench for far too long.

First, here are some photos of Darrell Eisner’s pen.

 photo DSC_0002_zpsufakvoeq.jpg

 photo DSC_0003_zpsrdgxpfy2.jpg

 photo DSC_0004_zpsypcwusiy.jpg

Below are the two vintage long short pens in need of restoration. The top group is an unbranded black bulb filler and the second narrative is a Diamond Point, a brand known by many collectors. As you can see, the unbranded bulb filler has a transparent barrel which had discolored quite a bit.  The Diamond Point had a hardened sac as well, and the usual nib – section – feed stains.

 photo DSC_0015_zpsb9txbynt.jpg

I made the decision to leave the bulb filler’s section alone. Separating the section/feed/nib from the barrel would have probably damaged the transparent barrel and I did not want to risk this. So I just ran the whole piece through the ultrasonic cleaner and left well enough alone. The breather tube was fortunately still in good shape and water tests showed that there was no leaking from the barrel, which did clear up a bit after cleaning.  I used a size 14 sac, trimmed to exactly one inch to complete the bulb filler by using sac cement to anchor it to the barrel, just below the clear threads. I then placed silicon grease on the clear threads to assure a smooth fit.  After finishing this, I cleaned out the inside of the cap and barrel end.  Finally, I tested the pen by filling with water overnight and testing for leaks.  None were found and it is ready to go.  Directly below is a close up of the completed filling system.  To fill, squeeze the sac (bulb) while the nib is submerged in your ink of choice.

 photo DSC_0002_zpsqewkrzqv.jpg

The second pen, a Diamond Point is shown below after being taken apart.  It is a standard lever filler, and these can be found in various colors.  You can see that it is a simple lever filler that has lost its sac and has severe staining issues.

 photo DSC_0016_zps7k8ftaqg.jpg

I cleaned the 14K nib in the ultrasonic cleaner and it is a very nice Warranted 5 nib.  I trimmed up a size 14 sac to about 1 inch and cemented it to the section.  You can see the resulting filling system below.  The small lever was still in great shape, and the barrel and cap needed little cleaning other than some polishing.

 photo DSC_0001_zpsmgzd1a7w.jpg

Here are both pens completed and ready to write.  The Bulb Filler measures 3 11/16 inches close and 5 7/16 inches posted.  The Diamond Point measures 3 13/32 inches closes and 5 11/16 inches posted.

 photo DSC_0003_zpsc3cgbad5.jpg

This photo shows how the Diamond Point cap screws onto the cap the second set of barrel threads when posting.

 photo DSC_0005_zpsaies6i90.jpg

 photo DSC_0004_zps3byzbwkn.jpg

Just for fun, and comparison, below are photos of a few additional long short pens. There are many more, but here are a few that I could find in my collection.

The Bexley Long Short – a cartridge filler that come in many colorful variations and is solidly made.

 photo DSC_0017_zpshnsmwqim.jpg

A previously restored c1941 Sheaffer Vacuum-Fil Tuckaway.  Note the threads on the back of the cap again, similar to the Diamond Point and Bexley.

 photo DSC_0019_zpsfgxennpo.jpg

 photo DSC_0020_zpsfwcogyyy.jpg

And finally, a contemporary Pilot (Japan) Elite Fountain Pen. Pilot has made numerous long short pens throughout their history. This is a current model.

 photo DSC_0023_zpsort6tzof.jpg

 photo DSC_0024_zpsbpdodwk4.jpg


June 1, 2015 Posted by | Diamond Point Fountain Pens, Long Short Pens | , | 1 Comment


%d bloggers like this: